RESEARCH CONCEPTS RC2000 Instructions d'exploitation Page 1

RC2K90INT-1, RC2K90INT-2, RC2KINT RC2000 Antenna Interface Box V. 1.10 Contents Subject to Change 6/28/01 Research Concepts, Inc. 5420 Martinda

RC2000 Antenna Controller Interface Box 10Figure 4

RC2000 Antenna Controller Interface Box 11Figure 5

RC2000 Antenna Controller Interface Box 12Figure 6

RC2000 Antenna Controller Interface Box 134.0 Heater Option A heater option has been developed for the RC2K90INT series of interface boxes. The KB E

RC2000 Antenna Controller Interface Box 14requires a pair of conductors. Since the RC2000 motor drive outputs are not actually carrying motor drive

15

RC2000 Antenna Controller Interface Box 16. 4.2.3 Antenna Motor and Limit Switch Connections The motor conductors should be sized appropriately for t

RC2000 Antenna Controller Interface Box 17Please refer to the discussion of these CONFIG mode items in the RC2000 manual. Failure to properly config

RC2000 Antenna Controller Interface Box 18(Buss type ABC, Littlefuse type 314, or equivalent). For more information on fusing please refer to the KB

RC2000 Antenna Controller Interface Box 19Quan Model/Description Manufacturer Comments (Ref Designators) 1 240 Ohm, 1 Watt Resistor (R6) 5 15

RC2000 Antenna Controller Interface Box 21. Introduction This document describes a family of products that allow an RC2000 antenna controller to inte

Prodelin 3.8m Antenna Installation Kit 20Prodelin 3.8 Meter Antenna (Model 1381) Installation Kit 1 Introduction This document describes an installa

Prodelin 3.8m Antenna Installation Kit 21given below for the shielded sensor cables. In addition to the motor control signals a pair of individually

Prodelin 3.8m Antenna Installation Kit 22Description of Conduit Run Conduit Run Starting Point and Conduit Fitting Type Conduit Length Cable Type/Le

Prodelin 3.8m Antenna Installation Kit 23does not come in contact with the sensor housing. Use the 3M Scotchlok connectors to make the connections.

Prodelin 3.8m Antenna Installation Kit 24Figure P1

Prodelin 3.8m Antenna Installation Kit 25 Figure P2

Prodelin 3.8m Antenna Installation Kit 26When all this has been completed connect the interface box to AC power. Please refer to section 2 for infor

Prodelin 3.8m Antenna Installation Kit 27CONFIG Mode Item Required Value for Operation with Prodelin 3.8 meter antenna Comments Attempts Position E

Prodelin 3.8m Antenna Installation Kit 286 Bill Of Materials Quan Model/Description Manufacturer Comments (Ref Designators) 50’ LA11-50 Electri

Prodelin 3.8m Antenna Installation Kit 297 Installation Checklist Before the installation, the following items should be addressed... 1. Fused AC

RC2000 Antenna Controller Interface Box 3Dual-Speed Antenna Azimuth and Elevation Movement The RC2000 antenna controllers use a pulse width modulati

Power PCB Relay 1

Power PCB Relay 2

Power PCB Relay 3

Power PCB Relay 4

KUL Series 5 & 10 Amp Magnetic Latching Relay 1

KUL Series 5 & 10 Amp Magnetic Latching Relay 2

KUL Series 5 & 10 Amp Magnetic Latching Relay 1

KUL Series 5 & 10 Amp Magnetic Latching Relay 2

KUL Series 5 & 10 Amp Magnetic Latching Relay 3

KUL Series 5 & 10 Amp Magnetic Latching Relay 4

RC2000 Antenna Controller Interface Box 4

Manual Revision History Manual Revision History 7/20/96 Revision 1.0 Included Appendix for Prodelin 3.8m 9/25/09 Added KPBP Operating Instructions

RC2000 Antenna Controller Interface Box 5Note that the scheme shown in Figure 1 does not support slow speed movement. RC2000 antenna controllers nor

RC2000 Antenna Controller Interface Box 6Many large antennas use a sensor attached directly to each of the fundamental axis of the antenna. The sens

RC2000 Antenna Controller Interface Box 7125 is designed for use with 120 volt AC line voltage. The KBPB-225 is designed for use with 240 VAC line v

RC2000 Antenna Controller Interface Box 8Figure 3

RC2000 Antenna Controller Interface Box 9The circuit associated with latching relay K4 is used by the RC2K90INT-1 interface box. With the RC2K90INT-